Cart (0)
Close
- Compatible for SAE J1939, CAN Open, DeviceNet, NMEA 2000
-
OPUS Display Connector Kit
$55.00OPUS 26 pin mating connector, contact pins and dummy plugs supplied as a kit. Part No: OPUSVF26001 -
Contactless reader CANCrocodile
$147.84CANCrocodile is designed for safe data reading from vehicle CAN bus. Contactless reader is used within vehicle telematics and GPS tracking systems for receiving various parameters of vehicle operation from CANbus: speed, RPM, oil pressure & temperature, fuel volume & consumption, etc. Data reading occurs without electrical connection and without damaging CAN wires. CANCrocodile works in “listen” mode only, i.e. it does not change original J1939 messages and does not send any signals to CANbus.- Nominal supply voltage: 12/24 V (5V – on request ; 2/24 A++ (low current consumption) – on request)
- Current consumption: 300mA for “5V” version; 30/15mA for “12/24V” version; 10/5mA for “12/24 A++” version
- Cable length- 0.7m (2 m– on request)
- Cable connector- Molex/bare wires/Special connector (specify when ordering)
-
Y CAN Cable 0.25 m Sub D9 (2 x Sub D9 female, 1x Sub D9 male)
$79.20Y CAN cable all pins connected length 25 cm, SUB -D9 socket to sub D9 socket and plug with shield. (similar to IXXAT Y CAN cable 1.04.0076.00001) -
Kvaser D-sub 9 pin 120 Ohm termination adapter
$63.80Kvaser D-sub 9 pin 120 Ohm termination adapter is a CAN adaptor with a 9-pin male D-Sub connector at one end and a 9-pin female D-Sub socket at the other. Between CAN High (pin 7) and CAN Low (pin 2) there is a built-in 120 Ohm CAN terminating resistor. -
OBD II to Sub D9 90cm
$63.36CAN Cable OBD II to Sub D9. This cable allows you to access the pins on your car’s OBDII connector. It has an OBDII connector on one end and a DB9 female CAN connector on the other. Overall cable length is 90 cm. -
Kvaser OBD II Extension Cable 15m
$561.00Kvaser's OBD II Extension Cable is a highly durable extension cable of 15 metres in length with male to female OBD II connectors. The cable is made of high quality thermoplastic rubber to ensure excellent flexibility and resilience. All pins are connected. -
Kvaser OBD II Extension Cable 5m
$265.32Kvaser's OBD II Extension Cable is a highly durable extension cable of 5 metres in length with male to female OBD II connectors. The cable is made of high quality thermoplastic rubber to ensure excellent flexibility and resilience. All pins are connected. -
Kvaser OBD II Extension Cable 2.5m
$196.68Kvaser's OBD II Extension Cable is a highly durable extension cable of 2.5 metres in length with male to female OBD II connectors. The cable is made of high quality thermoplastic rubber to ensure excellent flexibility and resilience. All pins are connected. -
Wire Harness 1.5m, with 81 Pin AMP connector, KS2
$475.20Wire Harness 1.5mts crimped to 81 Pin mating connector suitable for ESX-3XL STW34055 -
Wire Harness 1.5m, with 81 Pin AMP connector, KS1
$475.20Wire Harness 1.5mts crimped to 81 Pin mating connector suitable for ESX-3CM, ESX-3XM STW34054 -
Wire Harness 1.5 m, with 68 Pin AMP connector
$283.80Wire Harness 1.5mts crimped to 68 Pin mating connector suitable for ESX-C -
Wire Harness 1.5m, with 42 Pin AMP connector
$231.00Wire Harness 1.5mts crimped to 42 Pin mating connector suitable for ESX-IOX/IOXp - ESX-DIOM
